ENPLAS

Machined Parts

Product Category

Cast Nylon

- PA6G Natural
- PA6G MDS
- PA6G HI
- PA6GNF
- Enpals PA 6G GF
- Lubron 100
- Lubron 100S
- Lubron 150
- FE-Mid
- PA 12G

Polyacetals

- POMH
- POMC

Lubron :-

Enplas Lubrons family of cast nylons with enhanced lubricity. Both solid and liquid lubricants are incorporated into the material matrix; leading to low coefficient of friction, low wear rates and high limiting PV values.

A key characteristic of these polymers is that they can be quickly and easily machined and are an ideal replacement for many bronze and aluminum applications.
Due to their mechanical properties, Cast Nylons make an excellent low cost, load and sound reduction material. Their low co-efficient of friction makes them an excellent material for bearing applications, eliminating corrosion and reducing lubricating requirements.

One design constraint to bear in mind is that these particular polymers are hygroscopic. Enplas Cast Nylons are guaranteed to be free of pinholes and other defects.

Application

Lubron 100 :-

Enplas Lubron 100 is the most economical grade of the Lubron series. This grade has been successfully used in bearing and sliding applications. FDA compliant grades are available.

Property	Unit	Lubron 100
		Cast
Specific Fravity	--	1.14
Tensile Strength	MPa	68
Modulus of Elasticity	MPa	3200
Elongation at Break	%	50
Flexural Strength	MPa	103
Flexural Modulus	MPa	3620
Shear Strength	MPa	64
Compressive Strength	MPa	93
Compressive Modulus	MPa	2275
Hardness Rockwell	--	M85 (R120)
Hardness Durometer	--	--
Izod Impact	ft.lb/in(of notch)	1
Coeffecient of Friction	--	0.14
Limiting PV	ft.lbs/in2 min	6000
Wear Factor	in3min/ft.lbs.hr	90
Coeffecient of Linear Thermal Expansion	in/in/oF	5.6 E-5
Heat Deflection Temperature	oF	34
Glass Transition Temperature	oF	--
Metaling Point	oF	102
Continuous Use Temperature	oF	40
Thermal Conductivity	BTU in/hr ft2 oF	--
Dielectric Strength	Volts/mil	--
Surface Resistivity	ohm/square	--
Dielectric Constant, 108 Hz	--	--
Dissipation Factor, 108 Hz	--	--
Flammability @ 3.1 mm	--	HB
24 hour Water Absorption	%	0.3
Saturation Water Absoprtion	%	6
FDA compliance	--	No

Application

Lubron 100S :-

Enplas Lubron 100S grade has been developed where other grades fall short. This solid filled lubricant grade has been developed to meet growing demands for higher PV capabilities. It allows use at higher speeds and also exhibits superior stick slip characteristics

Property	Unit	Lubron 100S
		Cast
Specific Fravity	--	1.15
Tensile Strength	MPa	76
Modulus of Elasticity	MPa	2800
Elongation at Break	%	20
Flexural Strength	MPa	110
Flexural Modulus	MPa	3275
Shear Strength	MPa	69
Compressive Strength	MPa	97
Compressive Modulus	MPa	2760
Hardness Rockwell	--	M80(R110)
Hardness Durometer	--	D85
Izod Impact	ft.lb/in(of notch)	0.5
Coeffecient of Friction	--	0.18
Limiting PV	ft.lbs/in2 min	15000
Wear Factor	in3min/ft.lbs.hr	12
Coeffecient of Linear Thermal Expansion	in/in/oF	5.5 E-5
Heat Deflection Temperature	°C	94
Glass Transition Temperature	°C	--
Metaling Point	°C	215
Continuous Use Temperature	°C	94
Thermal Conductivity	BTU in/hr ft2 oF	--
Dielectric Strength	Volts/mil	400
Surface Resistivity	ohm/square	> 1E+ 13
Dielectric Constant, 108 Hz	--	--
Dissipation Factor, 108 Hz	--	--
Flammability @ 3.1 mm	--	HB
24 hour Water Absorption	%	0.3
Saturation Water Absoprtion	%	7
FDA compliance	--	No

Application

Lubron 150 :-

Enplas Lubron 150 combines advantages of Lubron 100 and MDS grades. It is Useful in wear components of materials handling equipment, gears and bushes.

Application

PA 12G :-

Enplas PA12 G possesses low moisture absorption, high dimensional stability, good mechanical properties

Typical Applications:

Gears, bushes, pumps. rollers, seals and several under water applications as well.

Application

FE MID :-

Enplas FE MID consists of a metal shaft inserted in a matrix of PA12 G. The bond between the interface of metal and polymer exceeds the sheer strength of Nylon. This allows gears of compact design for a given load. The composite works as an integral unit. These are available in diameters ranging from 50 mm to 300 mm and lengths of upto 500 mm.

Application

Engineering Polymers

High Performance Polymers

Machined Parts

Product Category